产品概述
描述
The ST1S50 device is a 500 kHz fixed frequency PWM synchronous step-down regulator. The ST1S50 operates from 4.0 V to 18 V input, while it regulates an output voltage as low as 0.8 V and up to 0.88 x VIN.
The ST1S50 device integrates a 95 mΩ high-side switch and a 69 mΩ synchronous rectifier allowing very high efficiency with very low output voltages.
The peak current mode control with a special PFM mode enables high efficiency at a light load.
The ST1S50 device is available in a VFDFPN10 3 x 3 x 1 mm - 10 leads package.
-
所有功能
- 4 A output current
- 4.0 V to 18 V input voltage
- Output voltage adjustable from 0.8 V to 0.88 x VIN
- 500 kHz switching frequency
- High efficiency at light load
- Programmable soft-start and enable
- Integrated 95 mΩ and 69 mΩ power MOSFETs
- All ceramic capacitor
- Power Good
- Cycle-by-cycle current limiting
- Short-circuit protection
- VFDFPN10 3 x 3 x 1 mm - 10 L
eDesignSuite
eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.
Power Management Design Center
Thermal-electrical Simulators for Components
Signal Conditioning Design Tool
NFC/RFID Calculators
Choose design tool: 
Power Management Design Center
Power Supply Design Tool
• SMPS design, by topology, by type and by product
• PFC design with analog and digitial control
• Supports various PCB configurations
Choose type: DC/DC AC/DC 太阳能电池充电器
Power Management Design Center
LED Lighting Design Tool
• Handles AC-DC and DC-DC design in common topologies
• Displays interactive and annotated schematic
• Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data
Choose type: DC/DC AC/DC
Power Management Design Center
Digital Power Workbench
• Provides a step-by-step optimized design of power section and control loop
• Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs
Power Management Design Center
Power Tree Designer
• Specify input/output power for each node in the tree
• Check for consistency
• Design each individual node
Choose design tool: 
Thermal-electrical Simulators for Components
AC Switches Simulator
• Select ratings and application waveforms
• Get junction temperature and blocking voltage graphs
• Search and sort suitable devices
Thermal-electrical Simulators for Components
Rectifier Diodes Simulator
• Select ratings and application waveforms
• Estimate power losses
• Search and sort suitable devices
Thermal-electrical Simulators for Components
STPOWER Studio
• Supports long mission profiles
• Provides power loss and temperature graphs
• Helps define heatsink thermal properties
Thermal-electrical Simulators for Components
Twister Sim
• Help select the right ViPOWER Automotive power device
• Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis
• Supports various PCB configurations
Thermal-electrical Simulators for Components
TVS Simulator
• Specify system ratings and surge waveform
• Search and sort suitable devices
Thermal-electrical Simulators for Components
Estimate
• Build simple schematics and firmware inputs in minutes
• Quickly generate reliable estimates of battery life, system power consumption and bill of materials costs
Choose design tool: 
Signal Conditioning Design Tool
Active Filters
• Handles multi-stage-designs and common topologies
• Returns circuit component values
• Provides gain, phase and group delay graphs
• Low Pass, High Pass and Band Pass
Signal Conditioning Design Tool
Comparators
• Handles most common configurations
• Returns circuit components values
• Provides I/O signal waveforms
• Inverting, Non Inverting, Window
Signal Conditioning Design Tool
Low side Current Sensing
• Returns circuit component values
• Provides current error graphs
Signal Conditioning Design Tool
High side Current Sensing
• Provides current error graphs.
• Help to select the right High side current sensing and shunt devices.
Choose design tool: 
NFC/RFID Calculators
NFC Inductance
• Input geometry and substrate properties
• Get antenna impedance
NFC/RFID Calculators
UHF Link Budget
• Enter forward and reverse link characteristics
• The tool returns link budget estimate
NFC/RFID Calculators
NFC Tuning Circuit
• Enter antenna parameter and matching target
• Select the topology of the matching network
• The tool returns component values for the desired design targets
您可能还会喜欢...
特别推荐
EDA符号、封装和3D模型
意法半导体 - ST1S50
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
符号
封装
3D模型
样片和购买
Don't show this again
| 产品型号 | 供货状态 | Budgetary Price (US$)*/Qty | 从ST订购 | Order from distributors | 包 | 包装类型 | RoHS | Country of Origin | ECCN (US) | ECCN (EU) | Operating Temperature (°C) (min) | Operating Temperature (°C) (max) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ST1S50PUR | | | distributors 无法联系到经销商，请联系我们的销售办事处 |
ST1S50PUR 批量生产
Budgetary Price (US$)*/Qty:
-
distributors
无法联系到经销商，请联系我们的销售办事处
包:
包装类型:
RoHS:
Country of Origin:
ECCN (US):
ECCN (EU):
Don't show this again